NU32905启动信息

本文地址：http://tongxinmao.com/Article/Detail/id/283

Connecting to COM13... 115200

Connected.

~ #

~ # ls

bin etc mnt sbin tmp var

dev linuxrc proc sys usr

~ # reboot

~ # umount: /dev/mtdblock0 busy - remounted read-only

umount: devtmpfs busy - remounted read-only

umount: sysfs busy - remounted read-only

umount: none busy - remounted read-only

umount: can't remount rootfs read-only

cannot run '/sbin/swapoff': No such file or directory

The system is going down NOWRTL871X: ERROR rtl8188fs_xmit_buf_handler: down SdioXmitBufSema fail!

RTL871X: rtw_cmd_thread(wlan0) _rtw_down_sema(&pcmdpriv->cmd_queue_sema) return _FAIL, break

RTL871X: ERROR rtl8188fs_xmit_handler: down sema fail!

[01/Jan/1970:00:04:09 +0000] caught SIGTERM, starting shutdown

[01/Jan/1970:00:04:09 +0000] exiting Boa normally (uptime 245videoin_close: current_task:RTSPServer pid:390

seconds)

00:04:09:354 main.c(61) Exit in signal handler: SIGTERM

+rtl871x_sta_deauth_ops, ff:ff:ff:ff:ff:ff is deauth, reason=2

ELOOP: remaining socket: sock=6 eloop_data=0x75c80 user_data=(nil) handler=0SnrReset

0-7

REG_GPBFUN = 0xff

x298c8

Sent SIGTERM to all processes

Sent SIGKILL toRestarting system.

enter to w55fa93_reboot()

Init RTC

DDR2 64MB

SD Port0 Booting Fail - No Device

NAND Booting Fail - Not for Booting

SPI Booting

- B0000004 = 0003076B

- B0000224 = 0000469E

- B0000220 = 000009EC

- B000020C = 00000018

- B000021C = 00000100

- B0000204 = FFFFFFFF

- B0003034 = 00888800

- B0003008 = 0000805A

- B0003028 = 21667525

- B0003000 = 04130476

- B0003000 = 04030476

- B0003010 = 00000005

- B0003004 = 00000021

- B0003004 = 00000023

- B0003004 = 00000027

- B0003020 = 00008000

- B0003024 = 00008000

- B000301C = 00002403

- B0003018 = 00000532

- B0003004 = 00000027

- B0003004 = 0000002B

- B0003018 = 00000432

- B000301C = 00002782

- B000301C = 00002403

- B0003004 = 00000020

- B00000A0 = 00000001

Success

ExeAddr 0x00900000

SPI Loader start (20161214 - gzip - NuWicam(DAC on)).

Initial GPIO pins for Nuwicam board.

N3290 UDC Library (20150820)

DAC On

Load Image Load file length 0x400, execute address 0x8090DB10

Check USB Status

N3290 MSC Library (20151208)

Connected to Adaptor

Load 2nd Execute image - Image No.2

Load file length 0x40, execute address 0xA00000

## Booting image at 0x00A00000 ...

Get Magic Number

Load file length 0x1DC1E2, execute address 0xA00000

## Booting image at 0x00A00000 ...

Get Magic Number

Gzip Uncompressing to 0x0 ... OK

Jump to kernelLinux version 2.6.35.4 (swt@swt-virtual-machine) (gcc version 4.8.4 (GCC) ) #6 PREEMPT Thu Nov 9 19:38:38 CST 2017

CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177

CPU: VIVT data cache, VIVT instruction cache

Machine: W55FA93

Memory policy: ECC disabled, Data cache writeback

CPU type 0x00fa5c30 is W55FA93

w55fa93_external_clock = 12.0 MHz

w55fa93_apll_clock = 988000 KHz

w55fa93_upll_clock = 192000 KHz

w55fa93_system_clock = 192000 KHz

w55fa93_cpu_clock = 192000 KHz

w55fa93_ahb_clock = 96000 KHz

w55fa93_apb_clock = 48000 KHz

Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128

Kernel command line: root=/dev/ram0 console=ttyS1,115200n8 rdinit=/sbin/init mem=32M vt.global_cursor_default=0

PID hash table entries: 128 (order: -3, 512 bytes)

Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)

Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)

Memory: 32MB = 32MB total

Memory: 24740k/24740k available, 8028k reserved, 0K highmem

Virtual kernel memory layout:

vector : 0xffff0000 - 0xffff1000 ( 4 kB)

fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)

DMA : 0xff600000 - 0xffe00000 ( 8 MB)

vmalloc : 0xc2800000 - 0xe0000000 ( 472 MB)

lowmem : 0xc0000000 - 0xc2000000 ( 32 MB)

modules : 0xbf000000 - 0xc0000000 ( 16 MB)

.init : 0xc0008000 - 0xc0085000 ( 500 kB)

.text : 0xc0085000 - 0xc0357000 (2888 kB)

.data : 0xc0358000 - 0xc0377280 ( 125 kB)

Hierarchical RCU implementation.

RCU-based detection of stalled CPUs is disabled.

Verbose stalled-CPUs detection is disabled.

NR_IRQS:32

Console: colour dummy device 80x30

console [ttyS1] enabled

Calibrating delay loop... 95.64 BogoMIPS (lpj=478208)

pid_max: default: 32768 minimum: 301

Mount-cache hash table entries: 512

CPU: Testing write buffer coherency: ok

devtmpfs: initialized

NET: Registered protocol family 16

bio: create slab <bio-0> at 0

Advanced Linux Sound Architecture Driver Version 1.0.23.

cfg80211: Calling CRDA to update world regulatory domain

Switching to clocksource w55fa93-timer1

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 1024 (order: 1, 8192 bytes)

TCP bind hash table entries: 1024 (order: 0, 4096 bytes)

TCP: Hash tables configured (established 1024 bind 1024)

TCP reno registered

UDP hash table entries: 256 (order: 0, 4096 bytes)

UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

NET: Registered protocol family 1

w55fa93_edma_init

JFFS2 version 2.2. (NAND) (SUMMARY) ? 2001-2006 Red Hat, Inc.

msgmni has been set to 48

alg: No test for stdrng (krng)

io scheduler noop registered (default)

W55FA93 uart driver has been initialized successfully!

w55fa93-uart0: ttyS0 at MMIO 0xb8008000 (irq = 13) is a W55FA93

w55fa93-uart1: ttyS1 at MMIO 0xb8008100 (irq = 24) is a W55FA93

brd: module loaded

loop: module loaded

m25p80 spi0.0: found GD25Q128B, expected w25q32

m25p80 spi0.0: GD25Q128B (16384 Kbytes)

Creating 2 MTD partitions on "m25p80":

0x000000200000-0x000000800000 : "UserData"

0x000000000000-0x000001000000 : "WHOLE"

i2c gpio scl=(0)3, sda=(0)4

w55fa93_gpio_configure()-0,3

w55fa93_gpio_configure()-0,4

Linux video capture interface: v2.00

memory allocate for port 1Planar buf 0 Phys addr = 0x38e000

Planar buf 0 Virt addr = 0xc038e000

Planar buf 1 Phys addr = 0x425000

Planar buf 1 Virt addr = 0xc0425000

Planar buf 2 Phys addr = 0x4bc000

Planar buf 2 Virt addr = 0xc04bc000

Packet buf 0 Phys addr = 0x553000

Packet buf 0 Virt addr = 0xc0553000

Packet buf 1 Phys addr = 0x5ea000

Packet buf 1 Virt addr = 0xc05ea000

Packet buf 2 Phys addr = 0x681000

Packet buf 2 Virt addr = 0xc0681000

jpegcodec_init

W55FA93 MMC/SD driver (20141219) has been initialized successfully!

SDHC card will run under 24MHz clock on SD port.

w55fa93evb_asoc_dev = 0xc1e49ca0 !!!

ret = 0x0 !!!, platform device added

******* global g_pw55fa93_adc_data address = 0xc1e392e0

0 = platform_driver_register

asoc: W55FA93ADC HiFi <-> w55fa93adc_cpu_dai mapping ok

ALSA device list:

#0: mach-W55FA93_ADC (codecADC)

TCP cubic registered

NET: Registered protocol family 17

Freeing init memory: 500K

Set <READY> to [heartbeat], Pin: GPB4

Set <LINK> to [mmc0], Pin: GPB5

Set <Reserve> to [gpio], Pin: GPB6

Mount APP root F/S

Run APP

BusyBox v1.15.2 (2017-09-25 15:12:56 CST) hush - the humble shell

~ # Wi-Fi network start

mmc0: card claims to support voltages below the defined range. These will be ignored.

mmc0: new high speed SDIO card at address 0001

http server start

Ser2net start

RTSP server start

gpio recover start

Stop ser2net...

killall: ser2net: no process killed

killall: boa: no process killed

Start ser2net...

Start boa http server...

**** GPIO Test Program ****

/sys/class/gpio/gpio5/direction

Start RTSP server...

/mnt/nuwicam/bin/RTSPServer -w 640 -d 480 -i 640 -e 480 -b 4096000

Auto-select RTL8189FS as a successor.

Jan 1 00:00:04 ser2net[342]: ser2net startup

Jan 1 00:00:05 spook[356]: listening on tcp port 554

VideoIn port 1 opened(0)

Auto-select RTL8189FS as a successor.

[01/Jan/1970:00:00:05 +0000] boa: server version Boa/0.94.13

[01/Jan/1970:00:00:05 +0000] boa: server built Nov 9 2017 at 19:38:14.

[01/Jan/1970:00:00:05 +0000] boa: starting server pid=344, port 80

Init GC0308

SnrReset

0-7

REG_GPBFUN = 0xff

Standard I2C.

Disable Mute

[OSS_RecOpen 626 {PID:356 } 5670] OSS fragment size 4096, App frames size 8000

driver i2c initial done

Sensor initial successful

video driver open successful

videoin_ioctl VIDIOC_CROPCAP

Mapping planar buf = 0

Function vin_ioctl_grab_frames - Line 547: Encode WxH = 640x480[SetPacketPipeWindow] Width , Height = 8, 8

[SetPacketPipeWindow] X , Y = 0, 0

jpegcodec is /dev/video1

JPEG file descriptor = 11

Overlapping is disable.

User Start Capture

Function vin_ioctl_grab_frames - Line 547: Encode WxH = 640x480RTL871X: module init start

RTL871X: rtl8189fs v4.3.24.8_22657.20170607

RTL871X: build time: Nov 9 2017 19:38:46

RTL871X: HW EFUSE

RTL871X: hal_com_config_channel_plan chplan:0x20

RTL871X: rtw_regsty_chk_target_tx_power_valid return _FALSE for band:0, path:0, rs:0, t:-1

RTL871X: rtw_ndev_init(wlan0) if1 mac_addr=60:c5:a8:69:83:df

RTL871X: rtw_ndev_init(wlan1) if2 mac_addr=62:c5:a8:69:83:df

RTL871X: module init ret=0

RTL871X: indicate disassoc

WisCam_60-c5-a8-69-83-df

Select a channel automatically

The rx cnt of channel 1 = 0

The rx cnt of channel 2 = 0

The rx cnt of channel 3 = 0

The rx cnt of channel 4 = 0

The rx cnt of channel 5 = 0

The rx cnt of channel 6 = 0

The rx cnt of channel 7 = 0

The rx cnt of channel 8 = 0

The rx cnt of channel 9 = 0

The rx cnt of channel 10 = 0

The rx cnt of channel 11 = 0

The rx cnt of channel 12 = 0

The rx cnt of channel 13 = 0

best_channel_5G = 36

best_channel_24G = 1

To scanning...

RTL871X: nolinked power save enter

The rx cnt of channel 1 = 9

The rx cnt of channel 2 = 4

The rx cnt of channel 3 = 2

The rx cnt of channel 4 = 1

The rx cnt of channel 5 = 0

The rx cnt of channel 6 = 6

The rx cnt of channel 7 = 0

The rx cnt of channel 8 = 1

The rx cnt of channel 9 = 0

The rx cnt of channel 10 = 3

The rx cnt of channel 11 = 4

The rx cnt of channel 12 = 2

The rx cnt of channel 13 = 0

best_channel_5G = 36

best_channel_24G = 6

The channel 6 is best.

Channel-->6

killall: hostapd: no process killed

Configuration file: /tmp/hostapd.conf

drv->ifindex=2

l2_sock_recv==l2_sock_xmit=0x0x75c10

ifconfig wlan0 192.168.100.1 netmask 255.255.255.0

RTL871X: nolinked power save leave

+rtl871x_sta_deauth_ops, ff:ff:ff:ff:ff:ff is deauth, reason=2

rtl871x_set_key_ops

Using interface wlan0 with hwaddr 60:c5:a8:69:83:df and ssid 'WisCam_60-c5-a8-69-83-df'

rtl871x_set_wps_assoc_resp_ie

rtl871x_set_wps_beacon_ie

rtl871x_set_wps_probe_resp_ie

rtl871x_set_beacon_ops

RTL871X: assoc success

My IP: 192.168.100.1

Starting DHCP server.

rtl871x_set_hidden_ssid ignore_broadcast_ssid:0, WisCam_60-c5-a8-69-83-df,24

rtl871x_set_acl

SoftAP mode is created.

[23.39] network-SoftAP done.

00:00:24:451 unabto_common_main.c(112) Device id: 'lx520.6983df.p2p.rakwireless.com'

00:00:24:452 unabto_common_main.c(113) Program Release 2.21005

00:00:24:454 unabto_app_adapter.c(398) Application event adapter using ASYNC model, queue length: 10

00:00:24:455 unabto_stream_event.c(237) sizeof(stream__)=3840

00:00:24:690 unabto_context.c(32) SECURE ATTACH: 1, DATA: 1

00:00:24:690 unabto_context.c(41) NONCE_SIZE: 32, CLEAR_TEXT: 0

00:00:24:692 unabto_common_main.c(171) Nabto was successfully initialized

00:00:24:709 unabto_attach.c(740) State change from IDLE to WAIT_DNS

00:00:24:710 unabto_attach.c(741) Resolving dns: lx520.6983df.p2p.rakwireless.com

~ # 00:00:39:798 unabto_attach.c(753) DNS error (returned by application)

00:00:39:799 unabto_attach.c(754) State change from WAIT_DNS to IDLE

00:00:41:819 unabto_attach.c(740) State change from IDLE to WAIT_DNS

00:00:41:819 unabto_attach.c(741) Resolving dns: lx520.6983df.p2p.rakwireless.com

上一篇：WisCAM使用方法
下一篇：Keil里面直接包含二进制文件